May 24, 2016

How to Measure a Glass Joint Size (10mm, 14mm, 18mm)

Measure Any Glass Joint: glass downstems and a diamond edge bowl slide on a white background

Updated October 2026 · Shatter Kitchen

To find a glass joint size, measure straight across the joint opening in millimeters: about 10mm is a 10mm joint, about 14.5mm is a 14mm joint, and about 18.8mm is an 18mm joint. Then check the gender: if the joint has an opening that accessories slide into, it is female, and if accessories slide over it, it is male. Size and gender together tell you which bowls, bangers, downstems and adapters will fit.

What are the standard glass joint sizes?

Nearly all bongs, dab rigs and accessories use one of three standard ground glass joint sizes. The industry settled on these years ago, which is why parts from different makers usually fit together.

Technical drawing of 10mm, 14mm and 18mm male glass joints drawn to scale with outside diameters of 10.0, 14.5 and 18.8 mm
Joint size Also labeled as Measures about Common on
10mm 10mm, "nano" 10mm across Mini dab rigs, dab straws
14mm 14mm, 14.4mm, 14.5mm 14.5mm across Most dab rigs, small to mid bongs
18mm 18mm, 18.8mm, 19mm 18.8mm across Larger bongs and beakers

The decimals cause a lot of confusion, but they are not different sizes. A 14.4mm, 14.5mm and 14mm joint are the same standard, just labeled with more or less precision. The same goes for 18mm, 18.8mm and 19mm. Shop by size with our 14mm joint and 18mm joint collections.

How do you tell if a joint is male or female?

Gender is simple once you see it. A female joint is an opening; the accessory slides inside it. A male joint is a ground tube; the accessory slides over the outside of it. Joints always pair opposite to opposite: a female joint on a bong takes a male bowl, and a male joint on a rig takes a female banger.

Most modern bongs and dab rigs have female joints, which is why most bowls and bangers sold today are male. You will still find male joints on older rigs and some specialty pieces.

How do you measure a glass joint with a ruler?

  1. Use millimeters. A ruler or tape with metric markings is easiest. Calipers are even better if you have them.
  2. For a female joint, measure the inside diameter across the very top of the opening, edge to edge.
  3. For a male joint, measure the outside diameter across the ground section, near the middle of the frosted area.
  4. Match to the closest standard. Anything near 10mm is 10mm, near 14 to 14.5mm is 14mm, and near 18 to 19mm is 18mm.
Technical drawing showing where to measure a glass joint: outside diameter of a male joint and inside diameter of a female joint opening

Measure the ground glass itself, not the thicker glass around it. On a female joint, the outer wall can be several millimeters thicker than the opening, which is where most wrong guesses come from.

Is there a quick way to check joint size without a ruler?

Yes, a US dime works well for female joints. A dime will sit on top of a 14mm female joint without falling in, but it drops right through an 18mm female joint. A 10mm joint is noticeably smaller than both, so it is easy to spot by eye. This trick is handy at the counter, but measure with a ruler before ordering if you are between sizes.

Does the joint angle matter?

For some accessories, yes. Joints are usually set at 90 degrees (straight up and down when the piece is upright) or 45 degrees (angled). Bowls and most bangers are made to work with either, but anything that hangs off the joint, like an ash catcher or a drop down, should match the angle of your piece so it sits upright. Our guide to choosing an ash catcher explains this in more detail.

What does a size like 18/14 mean on a downstem or adapter?

Two numbers describe two joints. On a downstem, the first number is the female joint it fits into on the bong and the second is the slide it accepts. Our 18/14 low profile slit cut diffuser downstem, for example, fits into an 18.8mm female joint and takes a 14.4mm male slide. Length is a separate measurement, covered in how to measure a downstem.

Adapters work the same way. An 18 male to 14 female adapter plugs into an 18mm female joint and gives you a 14mm female joint to use with 14mm bowls or bangers. Read drop downs, reducers and adapters explained to see every way you can change a joint, or browse all adapters.

What if my bowl or banger fits loosely?

A ground glass joint should seat snugly with a slight twist and not rock side to side. If a bowl wobbles, it is usually the wrong size or one of the joints is chipped. If it seats but feels loose, check for residue on the ground glass and clean both sides. Avoid forcing a tight joint; a gentle twist is all it should take. If you are deciding between a glass-on-glass setup and a rubber grommet stem, see glass-on-glass vs grommet bongs.

Keep reading

Frequently asked questions

Is 14mm the same as 14.5mm?

Yes. 14mm, 14.4mm and 14.5mm all refer to the same standard joint size. The decimal is just a more precise label.

Is 18mm the same as 19mm?

Yes. 18mm, 18.8mm and 19mm describe the same standard joint. Some sellers round 18.8mm up to 19mm.

How do I know if my bong is male or female?

Look at the joint where the bowl goes. If the bowl slides inside an opening, the joint is female. If the bowl slides over a ground tube, the joint is male.

Can I use a 14mm bowl in an 18mm joint?

Not directly. You need an 18 male to 14 female adapter or an 18/14 downstem, which lets a 14mm male bowl fit an 18mm female joint.

What size joint do most dab rigs have?

Most dab rigs use a 14mm female joint, with 10mm common on mini rigs. Check the product details or measure the opening to be sure.

Sold for legal use only. You must be 21 or older to purchase.